Usb Device Id Vid 1e3d Pid 198a Jun 2026
Right-click the device labeled "USB Mass Storage Device" (with the error). Select .
Note down the (e.g., CBM2199E ) and the Flash ID Code (e.g., 983A94937651 ). Step 2: Download the Target MPTool
: Varies widely from 8GB to "16TB" (though large capacities are often spoofed) Power Consumption : Max 100mA Review Analysis
| | Symptom | Likely Cause | Solutions | | :--- | :--- | :--- | :--- | | Driver Not Found / Unknown Device | Device Manager shows a yellow exclamation mark. | Standard Windows driver conflict or missing driver. | 1. Right-click start button and select "Device Manager". 2. Find unknown device, right-click, and select "Update driver". 3. Select "Search automatically for drivers". If that fails, click "Browse my computer for drivers" and navigate to C:\Windows\System32\DriverStore\FileRepository . | | Detected but 0 Bytes | Drive appears in File Explorer with a drive letter but shows 0 bytes used/free. | Firmware or partition corruption, often from improper ejection. | Chance of Data Recovery : Low, but possible with DMDE. Main Solution (Low-Level Repair) : Use CBM UMPTool or APTool . Follow the "Using UMPTool & APTool: The Fix" section. | | Fake Capacity | OS reports 64GB, but fails to write data beyond ~4GB. | This is a fake "capacity-expanded" drive. | 1. Test with H2testw : Write and verify full capacity. 2. Fix with UMPTool : After identifying true capacity, use UMPTool to re-flash firmware with correct parameters. | | Linux/macOS Detection | Not mounted or found in lsblk , but visible in lsusb / dmesg . | Often a driver or power management conflict. | 1. Check sudo dmesg -w when plugging in. 2. Try different USB port (preferably USB 2.0). 3. Install/update usbutils package. | | Bootable USB Failure | Cannot boot or write image with Rufus/BalenaEtcher. | BIOS boot sector corruption or configuration error. | 1. Use Rufus : With drive inserted, run Rufus, select drive, and click "START". 2. Low-level repair : If Rufus fails, use UMPTool. Erase the entire device, re-flash, then recreate bootable media. |
Try shifting the drive to a rear motherboard USB port. If it still fails to read, the device may need to be put into "Test Mode" by manually shorting specific pins on the controller circuit board. 💾 Firmware & Recovery Tools Usb Device Id Vid 1e3d Pid 198a
Click to initiate the production low-level flash cycle.
Every USB device uses a Vendor ID (VID) and Product ID (PID) assigned by the USB Implementers Forum (USB-IF) to tell the host operating system what drivers to load. ID Component Hexadecimal Code Identified Entity 1E3D Chipsbank Microelectronics Co., Ltd. Product ID (PID) 198A Mass Storage Flash Disk Architecture Common Microcontrollers ChipsBank CBM2098, CBM2199A, CBM2199E Protocol Interface USB 2.0 High Speed (Max 100mA current draw) Common Symptoms of Controller Corruption
Standard formatting utilities like Windows Format, Diskpart, or SD Formatter cannot fix a corrupted controller. To repair a device with , you must rewrite its internal firmware using native ChipsBank factory production software. Step 1: Extract Exact Hardware Details
This device is typically a . While functional for basic file transfers, it is not recommended for high-performance needs or critical data backups. It is also a common hardware profile for "fake capacity" drives sold on discount marketplaces. Key Specifications & Features Manufacturer : Chipsbank Microelectronics Co., Ltd. Right-click the device labeled "USB Mass Storage Device"
Some commercial environmental sensors (particulates, VOC, CO2) using a Chipsea MCU as a USB-to-sensor bridge may report this PID. For example:
USB Device ID VID 1E3D PID 198A, Chipsailing driver, fingerprint sensor driver, 1e3d 198a driver, Windows Hello unknown device.
A comprehensive database of PCI and USB hardware vendors and devices. DeviceHunt
The hardware identification string identifies a Flash Disk mass storage device powered by a Chipsbank Microelectronics controller . Operating systems read these specific numerical identifiers to map hardware devices to their appropriate software drivers. Step 2: Download the Target MPTool : Varies
Because Chipsbank controllers are frequently selected for ultra-budget storage, promotional materials, or unbranded clones, they are statistically more prone to firmware corruption than premium flash options. Users typically hunt for the keyword VID 1e3d PID 198a when experiencing severe errors. 1. "No Media" Error (0 Bytes Capacity)
This question appears frequently in forums because the VID/PID combination is unknown to most users.
. This specific hardware signature is most commonly associated with generic flash drives, USB sticks, and some counterfeit storage media. Device Specifications Vendor ID (VID): (Chipsbank Microelectronics Co., Ltd.). Product ID (PID): (Flash Disk / USB Mass Storage Device). Controller Part-Number: Often uses the controller. Typically USB 2.0 (High Speed). Power Consumption: Standard maximum current of 100mA. Common Use Cases and Issues
In the world of USB hardware, every device contains two critical identifiers: